Observe the requirements of the brick ties and the location of the final brick to determine exactly

Kitchen Tiles Home Services Movers htd Kurt Clean Izvozva Landscaping Painting Cleaning Pazardzhik Doors Suspended Ceilings Refurbishment House manager Conditioners Alarms Insulation Solar panels prefabricated houses for Us Site Map
Before commencing masonry must be made the necessary preparations. The construction htd site is cleared, the court of grout is placed about two feet from the building wall to the right of the worker; the same distance, but left stacked bricks. Necessary tools are placed in a convenient place so that they are handy. When the height of the wall exceeds 1 meter should be an appropriate scaffold.
Foundation on which to build the brick wall must be flat and horizontal. First, determine the location of the two end bricks of the wall, and they are put in place on the grout layer. Between them stretched string Spread grout and rank the remaining bricks in a row. When the tension of the string must be followed htd two rules. htd
Twine is stretched at the level of the upper front edge of the bricks; between him and bricks leave a distance of about 2 mm, so that it does not touch them. There are various devices for stretching the string, but lay terms this is the easiest of the two nails. In most cases, the procedure can not complete with all the brick that was placed initially.
Observe the requirements of the brick ties and the location of the final brick to determine exactly plumb. This method is slightly slower, but safer and therefore more suitable for amateurs. Horizontality of the lines is checked with a spirit level and verticality of the wall and the location of the final bricks - to plummet. It is important that the vertical joints between the bricks also to be filled with a solution to weld. This is achieved in the following ways:
- Before the brick be put in place on the forehead and from the set already applied solution brick trowel. Then the brick is placed on the wall by gently moves aside and tapping with a hammer or handle of a trowel until it fits into place;
- Bricks first intervene in place, and then the gaps between them are filled with solution. This is easier if the target in a separate htd container holds a rare solution. This method is the easiest, but also the slowest. So filled with shaped slats joints between bricks htd in joint masonry.
For grouting masonry selected without damage on the faces decorative bricks. These must be sorted htd and a thickness, in one row all the bricks should be equally htd thick. The joints between the bricks are most often formed by a square-section bars 10x10 mm. If necessary a small pointed htd trowel joints are filled with a solution, which was added and the cement, and then smoothed with fugach.
The solution is good for filling can be prepared with sand, screened through a sieve with a mesh size of 1.5 mm. Before it has hardened htd solution, all the dirt in the faces of the bricks should be washed thoroughly, because later cleaning is very difficult. When the wall will have a door or window, it is necessary to leave the corresponding opening.
You should know that windows and doors are marked htd with outer dimensions of their frames. Construction hole must be 20 mm wider and taller than the door or window. This requires precise izzizhdane bricks under constant control with vertical and level. Zidane relieve significantly htd the accuracy of the hole guaranteed if pre rigid wooden frame the size of the required opening. Bookmark and Share
Search for: Recent Posts Suspended ceilings - Advantages of Choosing interior doors Loader Equipment: Hitachi ZW95 choice of firm insulation neck trouble in housing services Tiles Kitchen Porters Kurt Clean Izvozva Landscaping Painting Cleaning Pazardzhik Doors Suspended Ceilings Refurbishment House manager Conditioners Alarms Insulation Solar panels Prefabricated houses Archive July 2013 (1) June 2013 (1) January 2013 (1) November htd 2012 (1) September 2012 (1) July 2012 (1) June 2012 (1) April 2012 (1) January 2012 (1) December 2011 ( 1) October 2011 (3) August 2011 (2) July 2011 (2) June 2011 (1) May 2011 (1) April 2011 (2) March 2011 (1) February 2011 (1) January 2011 (1) December htd 2010 ( 2) November 2010 (2) October 2010 (3) September 2010 (3) August 2010 (2) July 2010 (2) June 2010 (4) May 2010 (2) April 2010 (1) March 2010 (3) February 2010 ( 1) January htd 2010 (2) December 2009 (3) November 2009 (3) October 2009 (5) September 2009 (3) August 2009 (5) July 2009 (5) June 2009 (5) May 2009 (5) April 2009 ( 5)
2013 | All Rights Reserved